Download tce Placement Papers in MS Word and PDF Format for Job Interview

TCE (TATA CONSULTING ENGINEERS)

CAMPUSING AT JADAVPUR UNIVERSITY ON 14.07.2009 & 15.07.2009

DEPARTMENTS PARTICIPATED:

· INSTRUMENTATION & ELECTRONICS ENGG.

· ELECTRICAL ENGG.

· MECHANICAL ENGG.

· CIVIL ENGG.

· CONSTRUCTION ENGG.

PACKAGES:

3.24960 FOR B.E./B.TECH

3.76 FOR ME/M.TECH

SELECTION PROCEDURE:
· APTITUDE TEST

· TECHNICAL TEST

· TECHNICAL INTERVIEW

· HR INTERVIEW

APTITUDE TEST:

30 QUESTIONS 30 MIN
MCQ TYPE
SAMPLE QUESTIONS:
1. A PASSAGE ON HYPERTENSION 3 QUESTIONS FROM THERE

2. TWO JUMBLE SENTENCES.YOU HAVE TO MAKE THEM IN ORDER

3. TWO OR THREE WORD MEANING

4. STRUCTURE OF SENTENCES 2-3

5. MATHS FROM PROFIT AND LOSS 2

6. AREA OF ROMBUS

7. ARRANGE IN ASCENDING/DESCENDING ORDER

8. SIMPLE HIGHT AND DISTANCE MATH 1

9. SIMPLE GEOMETRY

10. GRAPHS, BAR CHART, CIRCLE DIAGRAM -10 QUESTIONS.

TECHNICAL PAPER: (INSTRUMENTATION)
30 QUESTIONS, 30 MIN
MCQ TYPE
SAMPLE QUESTIONS:
1. WHAT IS THREE ELEMENT CONTROL

2. WHAT IS INHERENT VALVE CHARACTERISTICS

3. WHAT IS MEANT BY Cv OF A VALVE

4. WHICH FLOWMETER DOES NOT DEPEND ON VISCOSITY CHANGES (EXCEPT CORIOLIS)

5. SPECIFIC GRAVITY GIVEN. STATE DENSITY

6. NAME A MASS FLOW METER

7. WHAT IS I-ACTION

8. WHY IT IS USED?

9. WHAT IS D ACTION

10. WHAT IS THE FLOW CHARACTERISTICS OF A VALVE (FLOW RATE Vs RATED TRAVEL)

11. WHAT IS USED FOR THE CONTINUOUS LEVEL CONTROL OF A TANK? (P/PI/PID)

12. MARK OUT THE TRANSDUCER (I/P,FLOW TX,ORIFICE)

13. PB GIVEN. FIND Kc

14. DEFINE THE TERMS REPRODUCIBILITY,REPEATABILITY,DRIFT,HYSTERESIS

15. WHAT IS THE DIFFERENCE BETWEEN EACH OF THEM?

16. ABSOLUTE PRESSURE AT SEA LEVEL IS 10mmHg. WHAT IS EQUIVALENT IN VACCUM?

17. NAME A BIDIRECTIONAL FLOW METER

18. WHAT IS THE FUNCTION OF ACTUATOR, POSOTIONER, IP CONV IN A PNEUMATIC CONTROL VALVE. KNOW PRECISELY

TECHNICAL INTERVIEW:
AVERAGE 20 MIN EACH PERSON. THRERE WERE TWO INTERVIEWER. ONE OF THEM WAS FROM ELECTRONICS. OTHER ONE FROM INSTRUMENTATION

1. TELL ME ABOUT YOURSELF

2. WHAT ARE THE SUBJECTS YOU HAVE READ

3. TWO WIRE Tx. KNOW VERY PRECISELY AND DEEPLY.

4. WHY 4-20 MA RANGE IS TAKEN?STATE ANY OTHER RANGES. LIVE /DEAD ZERO CONCEPT

5. HOW ACTUALLY THE SIGNAL AND POWER GET TRANSMITED OVER THE SAME PAIR OF WIRES. MIND THE CIRCUIT DIAGRAMS.

6. WHAT ARE THE PROCESS VARIABLES YOU HAVE MEASURED

7. BUBBLERS!!!!! VERY IMPORTANT TO TCE AS I THOUGHT!!

8. ADC TYPES. WHICH ONE IS MOSTLY USED?

9. SAMPLING THEOREM. WHO GAVE THIS. TWO ANSWERS!!

10. SAMPLE AND HOLD CIRCUIT

11. WHAT IS DOES? WHY NECESSARY?

12. ANALOG OR DIGITAL WHICH ONE IS MORE ACCURATE?

13. DIGITAL RESOLUTION. WHY 1/2LSB IS IMPORTANT? WHY IT IS USED TO SPECIFY THE ACCURACY OF AN ADC?

14. BASIC PRINCIPLE OF EMFM. IF THE PIPE IS NOT FULL WHAT WILL HAPPEN?

15. P CONTROLLER. WHAT IS PB?WHAT DOES IT SIGNIFY (SHOW WITH GRAPH)

16. WHY I CONTROL IS USED?

17. WHERE I CONTROL IS USED? (IF POSSIBLE KNOW SPECIFIC EXAMPLES)

18. ON OFF CONTROLLER. WITH GRAPH

19. WHAT TYPES OF PRESSURE GAUGES YOU HAVE SEEN?

20. WHAT IS THE BASIC FUNDA OF DP TYPE SENSOR?

21. KNOW IN DETAILS ABOUT CAPACITIVE TYPE DP CELL

22. WHAT IS THE DIFFERENCE BETWEEN INTRINSICALLY SAFE AND EXPLOSION PROOF?

FROM MY FRIENDS:

1. IDENTIFY P/I/D RESPONSE FROM A CURVE.

2. CORIOLIS-BASIC PRINCIPLE.CAN IT BE MOUNTED VERTICAL?

3. ORIFICE-TAPS WITH DIMENSIONS-CAN IT BE MOUNTED VERTICAL?

4. DIFFERENCE BETWEEN ORIFICE AND VENTURI. WHRER ARE THEY APPLICABLE?

5. THERMOCOUPLE RANGE. COLD JUNCTION COMPENSATION(VERY IMP)

6. MULTIPLEXER

7. SCHMITT TRIGGER.

8. WHY OFFSET OCCURS IN P CONTROL

9. WHAT IS MEANT BY INSTRUMENTATION?

10. WHY INSTRUMENTATION AND PROCESS CONTROL IS NEEDED?

11. PRESSURE RESPONSE OF A PIPE WITH ORIFICE INSTALLED

12. WHAT IS MEANT BY EXTRINSIC AND INTRINSIC SEMICONDUCTOR?

MATERIALS WHICH COVERS THE WHOLE THING:

1. NOTES FROM KM (MAINLY FROM TRANSMITTERS, LEVEL, FLOW(OROFICE),TEMPERATURE,PRESSURE),LIPTAK

2. PID CONTROLLERS(SEBORG AND OTHERS)

3. CONTROL VALVES (DCP, SEBORG AND INTERNET)

HR INTERVIEW:
THIS SELECTION WAS TOTALLY ON TECHNICAL INTERVIEW PERFORMANCE. IN HR THEY JUST ASKED ME ABOUT FAMILY BACKGROUND, WHAT I KNOW ABOUT TCE. WHAT TYPES OF JOB I LIKE? CAN I FULFIL THEIR REQUOREMENT? ETC

TCE PAPER ON 23rd AUGUST AT HYDERABAD

Hi frends.........,

This is K.Rupa from BHOJ REDDY ENGG COLL for WOMEN, Hyderabad. We attended Tata Chemical as an off-campous which held in TKR coll, Hyd. There r mainly four stages in the selection procedure.
They are like
(1) Written Test( The test consist of 2 parts Aptitude and Technical which is purely concept based ) Duration is 1hr( 30 min Aptitude & 30 min Technical ). Aptitude contain-30 questions & Technical contain-50 questions.
(2) G.D
(3) Technical Interview.
(4) H.R

Aptitude section:
This basically contain 5 verbal ques,n( synonyms-3 & antonims-2 ). This are so easy to be answered i got (1) FEIGN, (2)SPECIFIC, (3)TEMPLET sorry i dont remember this..., (4) TEDUOUS, (5)this is also so simple...
After this there are 5 ques,n based on Data Interpretation. They r so easy no need to worry about that later i got some 10 ques,ns based on algebra, like...
(1) cos 45= ?
(2) If a man covers 750km in 2hrs, then much dis can he cover in 5hrs 45 min
(3) Two trains problem, moving in opposite directions with some velocities 500 & 700 km/hr. The dis is 2400. then find the time taken for them to meet.
(4) There are many ques,n based on trains ...aprox 3-4 ques,n there are some ques,n based on areas like area of the sphere, cube is so and so ..... then find edge later i got some 10 ques,ns based on...

i dont know exactly but the que,ns are like
(1) The distance b/w the two circle present on the scale ( on the scale there r some circles of same size, separated by same distance )
(2) The scale contain some readings and some instrument is beside that, then what fraction of scale is covered by instrument.
(3) Some weight of 80kg is placed at one end of the pully, then how much wt must be added on the other side of the pully to make it balance.... the balanace is not placed exactly at the center , this is dis dependent the rest of the questions are also easy.......to say aptitude section is so easy

Technical section:
This is so hard one. in this there will be 50q to be answ in just 30 min. this section basically include main concepts, there is no need to worry for the people who r studing for GATE.
(1) Pecklet no. def
(2)They had some question from the stuff we study in +2 like ideal gas equation, vander wals eqn etc.
(3) nusselt no. is used when ........
(4) If temp inc then what happens to viscosity?
(5) Cox chart is used in ....Distillation, evaporation, drying r none
(6) Renolds no. is?
(7) Inertial forces to drag forces is called which no.?
(8) The stage belo saturation is called?
(9) Throtling is the process dependent on (options)Temp r Press r Volume

TCE PAPER ON 23rd AUGUST AT HYDERABAD

Hi frends.........,

This is K.Rupa from BHOJ REDDY ENGG COLL for WOMEN, Hyderabad. We attended Tata Chemical as an off-campous which held in TKR coll, Hyd. There r mainly four stages in the selection procedure.
They are like
(1) Written Test( The test consist of 2 parts Aptitude and Technical which is purely concept based ) Duration is 1hr( 30 min Aptitude & 30 min Technical ). Aptitude contain-30 questions & Technical contain-50 questions.
(2) G.D
(3) Technical Interview.
(4) H.R

Aptitude section:
This basically contain 5 verbal ques,n( synonyms-3 & antonims-2 ). This are so easy to be answered i got (1) FEIGN, (2)SPECIFIC, (3)TEMPLET sorry i dont remember this..., (4) TEDUOUS, (5)this is also so simple...
After this there are 5 ques,n based on Data Interpretation. They r so easy no need to worry about that later i got some 10 ques,ns based on algebra, like...
(1) cos 45= ?
(2) If a man covers 750km in 2hrs, then much dis can he cover in 5hrs 45 min
(3) Two trains problem, moving in opposite directions with some velocities 500 & 700 km/hr. The dis is 2400. then find the time taken for them to meet.
(4) There are many ques,n based on trains ...aprox 3-4 ques,n there are some ques,n based on areas like area of the sphere, cube is so and so ..... then find edge later i got some 10 ques,ns based on...

i dont know exactly but the que,ns are like
(1) The distance b/w the two circle present on the scale ( on the scale there r some circles of same size, separated by same distance )
(2) The scale contain some readings and some instrument is beside that, then what fraction of scale is covered by instrument.
(3) Some weight of 80kg is placed at one end of the pully, then how much wt must be added on the other side of the pully to make it balance.... the balanace is not placed exactly at the center , this is dis dependent the rest of the questions are also easy.......to say aptitude section is so easy

Technical section:
This is so hard one. in this there will be 50q to be answ in just 30 min. this section basically include main concepts, there is no need to worry for the people who r studing for GATE.
(1) Pecklet no. def
(2)They had some question from the stuff we study in +2 like ideal gas equation, vander wals eqn etc.
(3) nusselt no. is used when ........
(4) If temp inc then what happens to viscosity?
(5) Cox chart is used in ....Distillation, evaporation, drying r none
(6) Renolds no. is?
(7) Inertial forces to drag forces is called which no.?
(8) The stage belo saturation is called?
(9) Throtling is the process dependent on (options)Temp r Press r Volume
(10) which cycle is efficient (option) otto , air....